This ferrite ring will help keep unwanted electrical noise out of your servo. It is also a great way to shorten servo wires in a neat manner. The ring is 2.5 grams and can handle as many as 5 turns of 28ga servo wire. That is about 4 inches! Smaller wire can generate more turns. To wrap the wire, simply remove the 3 pin servo connector by lifting up on the plastic pins with a hobby knife. Gently pull out the wire. Thread the metal connectors through the ring as many times as you wish. For more glitch supression, please consider the Dionysus Design glitch reducer (DD-GLRD-PKG-01) which uses DSP filtering to always generate a clean signal.

The Brushed2Less controller allows you to turn your brushed RC system into a more powerful brushless one. It is great for upgrading ready to fly Helis such as the Blade CP and CX. The real advantage of this system is that it allows you to keep your current 4 in 1 ( Tail Speed controller, Receiver, Gyro and BEC ) system in place. In other words, you can keep your Piccoboard ( all in one system ) which comes pre installed on your Helicopter ( such as the Blade CP / CX / Honey Bee and others ) and simply piggy back a Brushless Speed controller and BL motor. You do not need a more sophisticated transmitter with this cool conversion. In order to complete the upgrade you must purchase 3 things:
(1) A Brushed2Less ESC
(2) A brushless Motor
(3) A brushless Speed controller. However there is no need to buy a separate ESC for the tail and there is no need to order a separate gyro, receiver or anything else. See the instructions below.

This micro pitch gauge is perfect for any micro helicopter such as the T-Rex, Blade CP and others. It has 11 degrease of both positive and negative pitch ranges enough to satisfy the most extreme 3D pilot. The handle is made of nice silicone material so its easy to get accurate readings.

Protect your machine when setting it up or when learning to fly with these properly sized training gear. The kit will allow you to survive not so perfect landings. The size of these training gear was specifically produced around the dimensions of a typical mini size Heli. It allows for minimum weight gain while still protecting your rotor blades from chipping do to a ground strikes and tip overs. The training gears also feature 30 degrease of carbon rod angle which allow for additional spring like protection from hard landings. Made with indestructible soft balls ( not ping pong balls which easily crumble ). This is a high quality product. Includes all you see in picture ( base has room to support up to six carbon rods ).

Replace the stock feathering shaft on the Blade CP with this precision grounded Titanium Feathering Shaft from Zero-G. The kit comes complete with socket head screws and additional brass spacers (shown in picture).

Another sophisticated mixer control board this one by E-Flight. Intelligently mix between the main motor and tail motor. Simply add a Gyro and have full microprocessor capable mixing for dual motor Micro Helis !!!

These ergonomic rubber-coated handles with rotating end caps are a 5 pc assortment tools specifically designed for Micro Helicopters. Hardened chrome with vanadium shafts and sockets tool. Includes precision 5.5mm nut driver with extra-long neck #0 and #1 Phillips screwdrivers 3/32 inch ball driver and .05 inch hex driver. A very hand tool pack to keep around your Helicopter.

Designed with a universal boom clamp this blade holder fits most Micro CP machines such as the Piccolo Pro Hummingbird Elite / Pro Blade CP E-Sky Hornet and others. The blade holder comes in blue and will help protect your blades from flapping around while you carry your favorite machine holding the rotor head.

Essential for the beginner heli pilot, turning any copter into a trainer. The set includes four plastic balls and light carbon rods. The gear attaches to helicopter skids and creates a larger base to promote safe landings, making the heli less likely to tip over. Fits the ESKY Honey Bee and other 300 size helis.

These are the same part as EK4-0009