The 3DX-300 Bell Hiller Complete CNC Head is designed for Blade CP and it also can fit Honey Bee CP2. You will need to reverse your collective pitch servo, and get the new main gear 3DX-UGE-30 .With all CNC precision parts and total 13 precision bearings, the 3DX-300 head will remove all the slop in the system. The new Bell Hiller design will provide more response than stock, perfect for 3D flying. This unique head incorporates a two upper mixing arm design. With this new Bell Hiller system, it can be determined how much main blades cyclic control comes from the flybar and how much comes from the swashplate. Thus, when the pilot inputs cyclic control, the main blades can respond immediately with the command. This will give the quick responses demanded by all pilots. Manufactured from 7075 aluminum, for strength and using double flange bearings on each mixing arm for ultra smoothness. The washout base is made of brass for lengthening the lifespan suitable for its function. This is a very good choice of material for washout base. The ring-linked outer pitch control linkage are now made with fully cnc aluminum to eliminate the flex in the stock plastic counterparts. It brings more responsiveness to the command. The CNC swashplate can be used separately with other stock parts on the head system and is included here. Very light weight.

A very economical six channel transmitter with CCPM mixing. The TX uses Futaba dual negative shift and comes with equipped with on / off 3D mixing switch and all channel reverse mode capability. This convenient inexpensive transmitter can practically fly any Fixed Pitch or Collective Pitch R/C Heli such as the Zoom / Shogun / ECO-8 / 16 Hummingbird Pro Viper CPX and others. Of course this transmitter does not have all of the bells and whistles that other higher end transmitters have but for this economical price you simply can’t beat it. This is an all in one practical beginner’s choice radio. Available from two distributors ( same product with different packaging ) including E-Flight and E-Sky.

The Complete CNC middle head unit replaces the stock plastic parts of the Blade CP / Honey Bee / Esky with this all CNC aluminum precision after market upgrade. The system comes pre assembled ( what you see is what you get ) and includes precision ABEC-5 bearings. The slider is so smooth it literally just drops down through the sliding pins. After installing the upgrade you will be amazed of just how much smoother your Helicopter becomes. The cyclic is more precise and the collective control becomes very soft and accurate. The upgrade comes highly recomended.

The Precision Main Blade Grips are designed to work on both Blade CP and Honey Bee CP2. The product is 100% aluminum CNC machined to provide best precision and durability. Moreover, the light and stylish high quality aircraft aluminum blade grips can help reduce the flex in the Blade CP head and improve cyclic response on the E-FLITE Blade CP/CP2 helicopters. This precision part comes complete with all mounting hardware ( spacers / screw / keys ) as well as installation instructions.

The 120 degree CCPM Swashplate version is designed to be used on the E-FLITE Blade CP/CP2 helicopter. Stylish and super light weight aircraft-aluminum swashplate is designed to bring best cyclic control and performance to your helicopter in all type of flights. Central Swash ball produced with stainless steel material to provide best durability and super smooth axis in all directions. The combination of the stainless steel center ball and high strength plastic ball housing will provide slop-free operation and ultra precise cyclic control.

The Vertical Tail Fin is machined from Carbon Fiber material, very light, strong and stylish. It is designed to protect tail rotor and tail motor during landing. Vertical Tail Fin is made with 1.50mm thickness Carbon Fiber sheet to minimize Tail Fin vibration. Used to replace the stock vertical rod on EFLITE Blade CP/CP2 and Honey Bee CP2 helicopters.

This is an ideal powerhouse motor for anyone using a Micro Heli with a brushed motor who does not want the hassle and expanse of migrating to a brushless motor. This awesome upgrade is a quick swap with your existing 300 - 370 brushed canned motor. Use the same wiring and same connector. Simply hook up the + and - and move the pinion over and you are done. And talk about power, coupled with a Lithium pack this motor will make your Heli go ballistic. This is a powerful 42,000 RPM, 21 Turns full ball bearing raced motor. Just what the Doctor ordered, for your Heli that is.

Replace the stock feathering shaft on the Blade CP with this precision grounded Titanium Feathering Shaft from Zero-G. The kit comes complete with socket head screws and additional brass spacers (shown in picture).

Modify your Honeybee or Blade CP with this high quality all aluminum CNC Swashplate and you will be amazed by the precision and stability gained. The part is blue anodized with a center brass ball. The center brass ball insured a super smooth cyclic control. Anti rotation pin is a metal rod which will sustain under most crashes. Precision ball ends come pre installed !!!

The all CNC tail system insures rigidity and solid tail control for the Blade CP and CP2. Available in both a single motor application ( same setup as stock ) or as a twin tail motor mount. The Twin motor version reduces the load on single tail motor of the Honey Bee CP2 and Blade CP by splitting the load into two separate tail motors. System includes stylish double ball bearings ( pre installed ). The boom mount is designed longer to hold the tail boom much better for both standard and twin tail motor mounts. Blue anodizing. Brings a total new look and clamps the motor really well. Moreover, the tail is very light in weight and is designed with double bearing support to turn your blade cp tail to a super smooth machine.

Replace the stock feathering shaft on the blade cp with this precision grounded Stainless Steel Feathering Shaft. The kit comes complete with socket head screws. Available from two manufactures. The Flight Tech version comes as a direct replacement straight through shaft while the Micro Heli version comes with the additional brass spacers ( shows in picture ).

This E-Flight ultra light 7.4V is made for Micro Helis such as the Blade CP E-Sky Honeybee and others. It comes with a balancing lead (see EFLC3100) which makes it an ideal pack. The 800mAh is lower capacity thus its very light and slim which insures long flight time and ultra responsiveness from your favorite Helicopter.