Xtreme Double PSA Strap is similar to our Single PSA Strap, but is designed to accommodate larger batteries and electronics. This Xtreme Double PSA Strap is designed with (2) ¾ Velcro® straps and a 5 adhesive back mount. Made from industrial strength Velcro and adhesive, to adhere to almost any surface. Package includes 1 Xtreme Double Strap, printed on both sides for use in any direction.

This LED pod by Lightning Power house 6 high quality LED lights. It can take input voltages ranging from 6v - 12v allowing you to fine tune the luminescence to fit your specific needs. Although this is sold as part of a NIGHT LIGHTNING night flying gear we are selling this unit stand alone as we realize the endless possibilities in multiple applications such as scale.

This unit comes with the leads attached making installation a breeze to the power source of your choice.

NIGHT LIGHTNING LED strips available by Lightning Power are the highest quality LED strips available on the market today. They are attached to 3M adhesive DS tape making installation simple and easy. You may resize them as simply as cutting them in the provided marks as small as 50mm or link strips together as simple as two solder points per attached strip. They can take an input voltage from 6v to 12v incrementing brightness by the input voltage allowing the modeler to fine tune the brightness to their individual need. The strips are available in blue, green, red or yellow in 1 foot and 3 feet strips.

Designed for the Night Ranger 3D and similar size Helis. Match these motors with Venom's V-Series 25 amp Brushless ESC and a 3S LiPo pack for amazing performance !!! The Venom V20L Series Brushless Motors pack a powerful punch yet still runs cool. Designed specifically for the Venom 3D but are also great motors for Helicopters such as the DragonFly 2 and all versions of the Hornet CP.

The JMD Models SLS (Scale Lighting System) offers many advanced features to make your flying experience much more enjoyable. Plug and Play Setup - Simply plugging the system into your receiver with BEC ESC lets you get up and running quickly without soldering. Light Weight - The system was designed with small models in mind and weighs very little for those weight-conscious modelers. ( 5 to 9 grams depending on the number of LED's ). Low Power - This system uses new Light Emitting Diodes (LEDs) which draw only a fraction of the power that an incandescent bulb does. Most modelers will not even notice any decrease in motor run-time or performance. 1 Beacon output - This ramping light will allow for realistic scale flexibility not offered in other systems. 2 Realistic Strobing Outputs - 2 Individual non-simultaneous strobing outputs provide incredible flexibility in how you chose to set up your system. 2 Controllable Landing Light Outputs - Now you can remotely turn on and off your Landing lights or other lights you plug into these outputs by the simple flip of a switch! 3 Solid Lamp Outputs - These solid lamp outputs are provided for powering Navigation lights and lamps for other requirements. Pre-wired Lamps - It is now as simple as plugging the lamps into a chosen output to achieve your desired lighting effect.

Rugged, lightweight APLG camera mounts from AskmanAP transforms your RC heli into a stable aerial photography platform. Various sizes are available. The 30 size APLG mount comes in two sizes, AP-30S and AP-30L. AP-30S fits the Logo 10, 14, 20 and the Century Swift. The large AP-30L is for the Trex 600 and Raptor. The camera mount is designed to handle up to about 2lb load. The design can be adapted for other helis that is not listed. It comes with two axis self leveling camera gimbal, that is damped with 3 aluminum body shocks. The mount weighs bit over 1 lb, but you will lose bit of weight since you will lose the stock LG. This is one of the lightest setups in the market. The optional Strap on kit (AP-SK) is available for Large (AP-30L) size mount for those who want a quick, detachable setup. The AP-50 APLG is designed for .50 and larger sized helis. Fits the Trex 600, Raptor and Jokers. This camera mount is designed to handle larger load. The design can be adapted for other helis that is not listed. It comes with Roll levelling HD camera gimbal, that is damped with 2 aluminum body shocks and 4:1 ratio tilt servo premounted for smooth tilt. The mount weighs about 1.5lb, but that is offset by the removal of the stock LG.

The Servo Rate Reducer will limit the rate of change for a servo signal. This will slow the servo down for use with retractable landing gear or airplane flaps.

The tools insures tha the front transmission of any X-cell Helicopter is level to the main gear and remains leveled. The tool may left on the Helicopter to continue proper operation and meshing of both gears.

Don't let it all hang out. Use a short antenna which will not decrease your total range. Many flyers actually stick the antenna on the inside of the canopy and make a detachable connector so the antenna becomes a single unit with the canopy. Are you tired of looking at your Heli with a 20 inches of antenna wire dragging behind it ? The 7.8 inch long STICKY antenna will effectively replace your long receiver antenna with minimum loss of range. STICKY is a flexible antenna which weighs only 0.5 gram. STICKY is tuned to the 72 MHz radio control frequency band. STICKY is only 0.007 (less than 0.2 mm) thick and has (you guessed it) a sticky backside you can peel-and-stick it anywhere. STICKY is photochemically etched on a flexible Mylar substrate similar to what you see in a printer head ribbon cable. The zigzag antenna wire as well as the base loading inductor are etched in copper. All exposed copper is then gold plated (hey REAL gold!) so that the antenna will yield minimum resistance and not be affected by corrosion. To use STICKY antenna you will cut the antenna of your receiver so that the total length between your receiver and the edge of STICKY is 5 inches. You may either solder the pigtail of STICKY to the remaining length of receiver antenna or you may use the supplied connectors. To attach to your Helicopter simply peel the paper backing off and stick the antenna to the fuselage or inside of the canopy. For optimum performance keep STICKY away from other electrical components carbon battery wiring etc. STICKY offers a minimum loss of range. To make sure you will fly safely always perform a range check prior to flight just as you would do with a full length antenna.

Glowire Helicopter Light kits. A very bright and intense light system with a fully potted F25 9-12 volt driver. The whole system runs of a 9V - 12V battery cell and so this system is ideal for mid size to full size electric or Nitro Helis such as a Logo ECO Raptor Eolo and others. With all of the new batteries now being used you have the versatility of using the same driver with different voltage batteries. The wire is very durable and very easy to work with as you may wrap it easily around your Helicopter. You may order the Super kit which comes with two 9-12V drivers as well as 8 ft and 10 ft of bright glow wire. The Super kit also comes with a more advanced driver. Also available is the standard kit which comes with a standard duel driver. And you may also order the driver itself and extra bright colored wires individually. If you are looking for the ultimate visibility with stunning night effects this kit is sure to produce great night flying visual effects especially when coupled with night blades which produce a bright rotational disk.

Xtreme battery straps have are perfect for securing things to your r/c heli! Xtreme straps are designed to wrap around batteries and/or electronics, to hold securely in place. Xtreme straps are ¾ wide and come in 2, 3, 4and 5 - inside diameter (adjustable). These straps are made from the highest quality ultra thin webbing and industrial strength Velcro®, with a very thin molded buckle. Tested and proven to be extremely durable. Product comes 2 straps per package. Choose from a selection of 6 vibrant colors:

Three set gold connectors with shrink wraps kit for Brushless Motors and Brushless Speed controllers. Gold connectors provide the best connectivity and also hold very well with matching gold coupler.

Now you can land on anything... Well almost anything. These are high quality full size floats for .30 - .50 size Helicopter. Easy to install and easy to remove. Great for Ice and water. Will keep your Helicopter floating.