Team Orion Avionics Gust Brushless Outrunner motor is the perfect solution for the majority of today's park flyers as well as many of today's 3D acrobatic helis needing a park 370 size motor. The Gust's Outrunner design allows for superior power and smooth response. Available in MS and MN models to provide the best specification for your application.

This is the electric powered, radio controlled, ready-to-fly Venom Night Ranger 3DXL Helicopter. For advanced helicopter pilots. FEATURES: Advanced Alloy Chassis, CCPM swashplate mixing for true 3D performance, V-Series 20L Brushless Motor, 6-channel FM radio with 4 micro servos, V-Series 20amp Brushless ESC, 3S 1500mAh 10C LiPo Battery, 2-3 Cell LiPo Balance-type Charger, Collective Pitch Rotor Head, Composite Landing Gear with aluminum skids, Carbon Tail Boom, Belt-driven Tail Rotor. Also available without electronics.

High efficient and high discharge suitable for the T-Rex 500 series and other professional model airplanes and helicopters. Max Continuous Discharge: 25C, Burst Discharge: 30C. Normal operating temperature is approx. 40-65 deg C(within 80% of rated discharge). Max. temperature: 80 deg C. Recommend to discharge the battery within 80% of rated discharge, keep 90% capacity when over 100 cycles, keep 85% capacity when over 150 cycles.(The cycle life and efficiency will reduce due to high current, high temperature and over-discharge).

These are Align 6S1P Li Packs. Max continuous Discharge of 20C/22C, Burst Discharge: 40C and normal operating temperature is approx. 40-65 ‹C(within 80% of rated discharge). Available in both the smaller 2100mAH pack as well as the larger 4600mAh pack. Align Lithium packs are designed around the Trex 450/500/600 so you are sure to get the results you expect.

This 8-10 cell motor is specially designed for more power and lower current consumption. This motor is the choice to tune your ECO for long flying times without sacrificing performance. This motor is the same as the one used in the the duration world record ECO-8 helicopter. 3.2mm shaft diameter. Sport and Performance motor are very similar with the Sport geared a bit more towards speed ( RPM ) Vs duration.

Hacker B50-15/16XL Heli version. This is a huge motor and has tremendous power. It was designed for Helis such as the Logo-20/24 and Bionic as well as .30 Nitro conversion Helis such as the eRaptor ( A.K.A RapE ) ane eHawk. Uses a 6mm shaft. 1052 RPM/V.

The C40 is Hacker's line of Helicopter motors. Designed to be robust and powerful with built in thin heat sink cooling fins to assist cooling the motor through the canopy the C40 produces tremendous results while still keeping ultimate efficiency and reliability. Available is several turn versions to accommodate for different gearing options. The motors use a standard 3.2mm shaft.

For 3-D flying on the Logo 10 or Eco-8. Powerful Hacker C50-13L is one of the ultimate motors. Eco-8 use 10 cells / 13-17T pinion. On Logo 10 use 10 cells / 14-19T pinion or 12 cells / 13-17T. Work very well with Lithium Polymers. Motor has 5mm shaft and integrated cooling fins. 1860 RPM/V

Hacker C50-15L Heli version. Awesome setup for the Eco-8 and Logo 10. Great power. For Eco-8 use 10 cells and 15-20T pinion. For the Logo 10 use with 10 cells / 16-21T pinion or 12 cells / 13-18T or 14 cells / 13-15T. Comes with 5mm shaft and cooling fins. 1610 RPM/V.

The Hacker C50 series were specifically designed for R/C Helicopters and are the best motors money can buy. These Motors have a 5mm shaft high temp magnets and integrated cooling fins. about 14 oz. and over 750+ RPM per volt. Very Powerful.

The Piccocontrol board consists of a BEC Mixers for main and tail motors and adjustment circuitry. All you need is to add a separate Gyro for a complete electronic system.

Dynam Mixer Gyro all in one board. The board is to be used in conjunction with 4 in 1 controllers such as the Vortex Mixer. The board comes with on board gain and mixer potentiometers. Small in size an very light this inexpensive mixer board is a solid electronic helicopter system.

The Piccoboard Lite comes complete with two electronic speed controller battery eliminator circuit Gyro with sensitivity / gain Gyro Reversing and best of all it is very affordable. Simply get a separate receiver of your favorite brand for a complete electronics package.

GWS 5 amp ESC is used to control the main motor with a separate components.

The add-on will allow you to remotely turn on and off simple Gyros such as the GWS PG-03 and others. Also the controler allows to connect more than one gyro at a time. The controler is small and can fit inside micro helis as well as full size helis.

The Picco Heli board is an ultra Lite and very compact board which comes complete with the Gyro Mixers and gain controls. The GWS PHA300 is only about 5mm thick and it is easy to both operate and setup. The PHA300 can be installed in Helis such as the Piccolo Hummingbird and others.

The Himax Power motor is similar in size and weight to the Hacker motor but are more economic and come prewired with gold connectors ( male and female ). The light weight and high efficiency Himax motor has a max of 60 000 RPM and comes with a standard 2mm shaft. They total up weight is only 1.7oz and are 32mm in length. The case can hold a temperature of up to 100C so the motor can pushed extremely hard for very long duration flight time.

The HF100 consists of two controllers and has been developed especially for use in micro-helicopters. One of the controllers is used for the main rotor motor while the second controller on the PCB is used to control the tail rotor - both with an extremely high 256 step sensitivity. With a 100kHz clock frequency they produce a longer life for both main and tail motors.

This cool looking power Outrunner motor uses an efficient brushless configuration to produce high torque with low overhead. Designed specifically around the MX400 Ark Helicopter this motor is available in a 12 Pole configuration producing 3600 KV of pure power as well as in 6 Pole 2280 KV. The motors come with pre wired male bullet gold connectors as well as a set of female bullet gold connectors to match.

The NHM is produced by JR Heli division specifically for R/C Helis such as the Voyager E and other Helis in the 540 range. Motor comes with pre wired connectors.

The Atomic Force motor has great power considering it is a brushed motor ( i.e. you can use your existing fusion electronic speed controller ). The motor has 30% more power than the stock fusion Lite Machines motor and will also allow for longer flight time so if you are looking for an inexpensive replacement brushed motor for the corona well this is The Atomic Force.

Specifically designed for Micro Helis with both linear and constant RPM mode integration. Two versions are available Standard which works for brushless motors such as the Hackers Model motors and other. Twister which was designed specifically around the outrunner twister-x motor ( See Motors section of site ). The MS controllers are known for being very reliable and bug free in software and firmware revisions. Choose the type that's right for your application.