Hornet II Complete Collective Pitch Hornet with best mods no TX /F
This discount package comes with the following products: - MS700 Hornet II CCPM Basic Kit
- IP5890 Hornet CP Head Block with Pin Set Screw
- GWS-R6NF Receiver 6 CH Futaba
- GWS-PG03 GWS PG-03 Micro Gyro
- IP5821 Aluminum CNC Hornet Bell Crank
- HRC31050 HS-50 HiTec Servo
- HRC31050 HS-50 HiTec Servo
- HRC31050 HS-50 HiTec Servo
- HRC31050 HS-50 HiTec Servo
- GWS-MC2002 GWS Charger
- IP5820-1 Hornet Titanium Shaft CP
- GPMP0107 Powerex Turbo 7 / 8 / 9 Cell Pack
- IP5835 2mm Titanium Tail Shaft
- GWS-ICS100E 5-amp Speed Controller
- HH104 BEC Male Connector
Complete Fixed Pitch Schweizer 300 with mods and TX
The package includes the Micro Scale like Schweitzer 300 Helicopter as well as free Tail bearings.The kit is great for beginners allowing the flyer to start with a Fixed Pitch machine now and upgrade to a collective Pitch ( MS500 ) in the future.
Complete Fixed Pitch Hornet Sport and best mods and TX
The package includes the Micro Sport Hornet Helicopter as well as included upgrades such as the CNC bell crank tail bearings titanium main shaft titanium tail shaft and more. The kit is great for beginners allowing the flyer to start with a Fixed Pitch machine now and upgrade to a collective Pitch ( MS500 ) later.
CPX Complete Collective Pitch Hornet with best mods and TX
The package includes the Micro Sport Hornet Collective Pitch Helicopter. A 3D machine with aerobatic capabilities. Included mods are the CNC bell crank CNC Head Block tail bearings titanium main shaft and titanium tail shaft as well as wider drive shaft bearings for additional internal boom support. The Hornet uses the latest eCCPM mixing which can be configured using the optional eclipse 7 transmitter. Fly indoor or outdoor with this amazing micro.
The Hornet X-FP is a very good versatile beginner’s Micro Heli which comes with a fixed pitch head ( which later on may be upgraded to a CP head ). A fast yet simple machine for fliers which plan on growing with the Hobby. This kit contains the Hornet X FP (Fixed Pitch) micro helicopter the basic type of the MS Hornet X family. This model is designed mostly for beginners for its simple construction and setup and that it can be flown using a simple four channel airplane R/C transmitter. Because of the fixed pitch construction no deep skills on RC Heli setup are required. The model can be used both for indoor and outdoor flying. The kit is available as an 80% almost ready to fly kit or as a completely disassembled kit.
- Main rotor diameter 490mm - Body length 510mm - Motor 300 Series - Flight weight 320g - Accu 2-3 Cell Lithium Pack or 7 - 8 cells NiCd/NiMH - Flight time 10-15 minutes with Lithium pack
Crash Kit-S conical gear
- 1 E002 main gear - 2 E003 undercarriage frames - 2 E006 undercarriage legs - 2 E018 pinion gears - 1 E039 main shaft - 1 E040 retainer - 1 E064 tail fin
Hornet CPX Kit. CCPM Head. Carbon Fiber Fins. Carbon Fiber Main Blades. Carbon Fiber Boom support. Threaded Flybar. 3D Paddles ( New ). Pre assembled tail hub. Metal tail shaft. Decal Sheet. Instructions.
MS Hornet X CP ARF 80% Micro Electric Helicopter
The Hornet X-CP is a very dynamic machine with a fully CCPM 3D head ( none bell hiller ) which allows for the most aggressive cyclic and serious performance machine. A very light machine with lots of power the model is designed for moderate to advanced RC Heli pilots mainly for dynamic flight and basic aerobatics. It represents an ideal entry model for Heli aerobatics exercise. Hornet X CP uses CCPM mixing system-direct three-point swashplate control without mechanical mixing. This means that your transmitter must have this mixing built in. Hornet X CP can be used both for indoor and outdoor flights. The kit is available as an 80% almost ready to fly kit or as a completely disassembled kit.
- Main rotor diameter 560mm - Body length 510mm - Motor 300 series - Flight weight 340g - Accu 3 Cell Lithium Packs or 7 - 8 cells NiCd/NiMH 700mAh - Flight time 10 to 12 minutes on Lithium packs
Hornet II CCPM Basic Kit
Based on the Hornet CP. Longer symmetrical main blades Longer carbon tail boom. CCPM 120° precision swashplate. Battery support Component deck. Pe-built landing gear assembly. Sleek looking lightweight canopy Dual tail boom support struts. Horizontal fin. Pre-installed motor capacitors. Motor not included in this kit
MS Hornet X 3D Brushless Kit with motor and ESC
The Hornet X-3D is probably the most aerobatic Micro Helicopter in the market. The power to weight ratio is the lowest allowing for an extremely versatile and aerobatic machine. The X-3D includes many improvements. This model is designed for Advanced RC Heli pilots and can (without any further tuning or modifications) perform highly demanding 3D aerobatic maneuvers. Bell-Hiller mixer greatly improves the model maneuverability. Hornet X 3D uses CCPM mixing system - direct three-point swashplate control without mechanical mixing. This means that your transmitter must have this mixing built in. The Hornet X 3D can be used for both indoor and outdoor flying and it represents the most advanced technology in micro helicopter performance and capabilities. Kit includes 19 ball bearings. The kit is available as a Barebones kit as well as with a brushless motor and ESC.
- Main rotor diameter: 560mm - Body length: 510mm - Motor: MS Twister EM300/20 - Flight weight: 340g - Accu: 3 cells LiPol 1000mAh - Flight time: up to 10min
Seaknight Helicopter Kit with Brushless Motor
The CH-46 Sea Knight helicopter is used by the Navy for shipboard delivery of cargo and personnel. The CH-46E is used by the Marine Corps to provide all-weather day-or-night assault transport of combat troops. The CH-46 is based on the Hornet head design and it is powered by a powerfull dual shaft brushless motor. The kit is available with a barebones kit + a brushless motor or as a package deal. The kit is designed for the expirianced modeler and it is truelly a magnificent Micro Heli to fly and look at.
- Basic kit includes: Helicopter and Brushless Motor - Package kit includes: Everything you need to fly except on board battery pack receiver crystal and Transmitter those items are available separately - Semi-scale RC model 1:24 - Highly attractive twin-rotor construction - Full ball bearing construction - Unique and protected solution of the twin rotor system drive - Microprocessor based mixing of the control signals for the twin-rotor - Basic parts are produce with CNC technology - Only one electric engine for twin-rotor - Two gyros for high stability - It is not necessary to use special radio transmitter standard 5 chanels - Rotor diameter: 490 mm - Fuselage Lenght: 560 mm - Overall Lenght: 890 mm - Total weight: 700 to 800 mm - Motor: brusless with rotating housing - Flight Time: 5 to 12 min. accu depend
HeliHobby.com is your source for Remote Control RC Helicopters, products, modifications and more. Full Range of Nitro, Electric and Micro Helis in stock
