Indestructible very light-weight and precise grips enable extremely smooth (ball bearings) movements of the tail pitch slider. These grips will work for all types of Hornets. An essential upgrade for a perfect tail control in combination with a good gyro. Mounting does not require any modifications of the original tail mechanism it is enough to simply replace the blade grips and secure them by included screws.

A set for a comfortable mounting of the brushless motor AXI 300/20 (MS-116) behind the main shaft. This upgrade enables an easy adjustment of the center of gravity for differed battery packs because it frees the place in the front part of the helicopter for easy mounting of the packs. The main gear with the teeth on its inner side provides a perfect transmission of the motor power to the rotor blades even with small motor pinions. The diameter of the main gear is very small and the wheel is hence well protected by the body frame. The set is highly crash resistant and the level of noise is low. It also enables a very comfortable pinion change and enough space to achieve an optimal gear-mesh.

These are a direct bolt on for the Hornet CP. They are a cord taper design and have superior rigidity over all other blades. They will give much better cyclic response and they will make your Hornet track very well. The quality you expect from MAH.

Replace the flexing collective horn with this hard CNC collective horn. The grub screws are built onto the horn for additional strength between the horn and the flybar. Slot were added to reduce weight making the part lighter than its plastic counter part. Comes equipped with two CNC precision ball ends. The horn really makes a big difference in collective control and comes highly recommended.

Did you loose your shaft pins or just want new ones? These high-quality pins are made from stainless steel and precision ground to .0395 . The ends are rounded for easy insertion into the main shaft.

The CNC X-Pro swashplate was designed for the pro flyer with shorter arms allowing for more responsive cyclic control. Ultra light design and super smooth ABEC-5 bearing makes this swashplate a key component in fast forward flight 3D maneuvers and extreme aerobatics. CNC ARS is sold separately and it is required when installed on a Stock Hornet CPX or Hornet II

The ultimate frame for the Hornet is just that a superior design and genius construction. This upgrade converts any Hornet onto a solid machine which requires no glue for assembly and introduces many core advances. Some of the advances include a threaded main post for easy assembly / removal ultra light design delrin struts interior aluminum support 120 degrees aluminum servo mounts and much more. The upgraded frame comes pre assembled and equipped with all socket head screws. The boom locks onto the frame using a set screw. It is simply “unreal” how light this frame is when holding it you will be amazed. The total up weight of the frame is only a bit over 50g and every part was designed with the least amount of material in mind to achieve such great results. The carbon frame structure is made of two sandwiched CF plates which lock onto the center aluminum core using inner aluminum frames. The CF frame also has a built in tail servo mount. The frame is to be used with the HS-55 servos or equivalent. The setup allows for both front and rear 120 degrees setup. The the kit also comes with anti rotation support ( not shown in pictures ) as well as a complete clamp set for your 7mm booms ( Vertical Horizontal fin clamps as well as a boom support clamp ). The center core is made of aluminum thus the motor disperses heat directly onto the center frame allowing for a cooler running motor. All in all this is the best thing you can do for your Hornet !!!

The CNC machined gears will run extremely true and will not cause vibration like the stock molded gears. Use a pair of 18T gears for direct replacement or one 18T and one 16T tail gears to increase the speed of the tail rotor and maximize tail authority while maintaing the speed of the drive shaft. The gears are made of high quality delrin and so they are very strong and light. No external lubrication is necessary. For best results use the gears in conjunction with Titanium tail shaft (PART#HH183). Both gears should be installed using the L0261 flanged bearings. If used with the stock CF tail shaft then the shaft may require to be sanded down a bit for easy installation. The gears are a tight fit and so no CA is necessary for secure installation.

Extra thin and very crash resistant fin set. Made from carbon fiber plates and bonded to the boom using CA. The set include both a vertical and horizontal fin set. Improve your flying control and assist lift and drag with these high quality fins.