Measures 3 x 1-1/2 x 1/2 inches (camera only), 1 oz. FEATURES: High resolution, LCD display, rotating lens, long battery life, and a thermal activated motion detector. Video camera includes audio, still photos, a voice recorder, USB drive, and a Webcam. Unit is small enough to mount on just about any model airplane, small parkflyers, RC cars, trains, skate boards, or even a kite. Can be remotely activated using an additional servo. Videos are recorded with a resolution of 640x480 for clear playback, complete with sound, and 1280x1024 pixels for still photos. Camera lens rotates 90 degrees so you can take photos or video from multiple angles. Built-in rechargeable 200 mAh Li-Ion battery that charges via the USB port on your computer in about 1 to 1-1/2 hours. For video and audio-recordings, FlyCamOne2 requires a minimum sustained write speed of 9 megabytes (MB) per second and a read speed of 10MB per second (not included). With a 2GB SD card (not included) the video recording time is about 30 minutes. Webcam use requires the included software and USB cable. No software required for all other uses! You can edit and compress the .avi video files using Windows Movie Maker, included with Windows XP SP2 and Windows Vista.

This is AskmanAP Pan APLG system. The LG is designed to rotate with the camera mount, giving you a full 360 degree panable system. To protect the gearing and servo, there is a unique friction clutch in the pan system. It comes with universal mounting plate with detachable strap on plate. 30 size model fits the Logo 10-20, Swift, Raptor and Trex 600 while the 50 size works with the Raptor, Trex 600 and Joker. The design can be adapted for other helis that is not listed . It comes with semi-rigid 5x5 (6x5.3-50 size) inch camera gimbal, that can mount the camera in portrait or landscape mode. The mount weighs a bit over 1.5 lbs and comes with pan and tilt servo.

AskmanAP produces an Aerial Photography Landing Gear (APLG), designed specifically for the T-Rex, which can carry a small camera. Due to the small size of the T-Rex, the challenge was to make the APLG strong and light weight. The AskmanAP APLG replaces the original T-Rex landing gear. The APLG illustrated is the new V2.0 T-Rex platform which has a 5 inch carbon fiber (CF) camera mount and floating mounting system for better vibration damping. It has more standard feature than any other available mount.

Cool accents for your heli rotor blades. The BladeFx currently comes in 2 sizes. The small is designed for the mini helicopters such as the Trex-450, X-400 and Raptor mini Titan and are 9 inches long and approximately 0.75 inches wide. The large size will fit any full size heli and are 18 by 2 inches (approx.). They are cut from high grade material. We have tested these on a Trex 600 and we have 30 flights and still going strong. We also have 15 flights on a nitro machine. Available in several designs with more to come. Click on the picture below to view.

Wouldn't it be cool to walk on water ... ? Well you can't, but at least with these cool and inexpensive Heli floats from Century Helicopters you can now land on water. The Helicopter water floats can also be used on snow and other soft surfaces. Hard cover insures the balloons will not rapture. Blue in color and still very light so they do not put a heavy load on your radio controlled machine.

This tool will help you make your own push rods for linkage systems. 2mm Cutting Die w/handle. Now you can easily make your own rods with a threaded end. Fix old push rods or make custom length rods with this cool little tool. The hard handle insured a proper grip and the Complete kit is a must have for any true hobbyist.

Even with the right precautions, there is always a chance that Lithium batteries might catch on fire. Protect yourself with the Lipo Safe Charging and Storage Bag. Check out the video below. The Lipo Safe is an easy to use safety device for charging your Lipos. It's a definite must for all Lipo battery users.

This ferrite ring will help keep unwanted electrical noise out of your servo. It is also a great way to shorten servo wires in a neat manner. The ring is 2.5 grams and can handle as many as 5 turns of 28ga servo wire. That is about 4 inches! Smaller wire can generate more turns. To wrap the wire, simply remove the 3 pin servo connector by lifting up on the plastic pins with a hobby knife. Gently pull out the wire. Thread the metal connectors through the ring as many times as you wish. For more glitch supression, please consider the Dionysus Design glitch reducer (DD-GLRD-PKG-01) which uses DSP filtering to always generate a clean signal.

This base loaded antenna was designed specifically for micro helicopter but it can also be used on all other 72mhz aircraft. The body is CNC machined fiberglass with a stiff music wire antenna. It is entirely coated in plastic to prevent electrical contact with carbon fiber or any other conductive material. The body is completely flat on the back to allow mounting with servo tape. The edges have groves that allow it to be tied to the model with a zip tie or wire. The wire is stiff to reduce the amount of antenna vibration when the model suffers from vibration due to unbalanced rotor blades or propellers. A single pin connector is included and should be soldered to the receiver antenna after it is cut to 3 to 6 inches. The Sting Ray was scientifically designed to provide the best possible performance at the lowest size and cost.

With its versatility and small size, the Air Alert Low Voltage and Lost Aircraft Alarm is a must-have accessory for fliers everywhere. This compact, on-board system emits different sequences of beeps to signal potentially risky flight pack conditions. Low Battery Alarm when flight pack voltage levels are low, to identify an impending power failure.

Firefly lights are an attractive, easy to use lighting system for your R/C heli. Just plug the Firefly light into a spare receiver channel, or use a separate 5V source. Fireflies each have several bright LEDs that slowly glow on and off. The lights can be switched from glow mode to continuous lighting by using your radio. If no signal is present or the signal wire is cut, the lights will default to glow mode.

EasyLights are an attractive, easy to use lighting system for your R/C heli. Just plug the light into a spare receiver channel, or use a separate 5V source. EasyLights each have a pair of ultra bright 10,000mcd white LEDs. The lights can be switched on and off by using your radio. If no signal is present or the signal wire is cut, the lights will default to being on.

Sinewinder is an attractive, easy to use lighting system for your R/C vehicle. Just plug the Sinewinder light into a spare receiver channel, or use a separate 5V source. Sinewinder has 12 bright LEDs that scan from side to side, with a short trail after the leading light. The lights can be switched on and off by using your radio. If no signal is present or the signal wire is cut, the lights will default to being on.

The DELight Starter Kit combines all the components of the DELight programmable lighting system into one package. It consists of a programmable lighting controller, software for creating customized lighting sequences, a USB link cable to load the programs and ultra-bright LED lights. Everything you need to create scale, sport or nightflying effects for R/C airplanes, cars, robots or special effects is included. The DELight Ultra Bright LED's are the brightest LED's ever used in an R/C lighting system. They are up to 15 lumens each and can each draw up to 150mA. Not to worry, the DELight controller can handle this level of power, and if you're worried about blinding yourself, the controller has programmable brightness!

HeliHobby T-Shirts and Caps. We thank you for your business and we thank you for your support over the years. The shirts are made of Hanes Heavyweight material and are 100% preshrunk cotton. The Baseball cap is of one size fits all and comes with a sawn HeliHobby logo on the front.

These stickers have an applicator where you peel the back off, place the sticker onto the surface area of where you intend to stick it and then remove the front for a professional look. These stickers are made of high quality and are intended to stay stuck where you stick them.

We will send you these stickers for free if you are entering our Stick It contest!

Use these quick-lock ties again and again. Built-in easy release latch holds securely until you open it.

Excellent for straping and securing battery packs and other electronics.

Stop flying while guessing when will your main pack run out. With this inexapnsive little gadget you can fly with confidence. Simply hover in front of you and read out the bright LEDs. If one of the LEDs turn RED you know its time to land, its that simple. Designed for one to three cell Lithium batteries and plugs directly to the balancing plug.

This unique display of lights will help your R/C aircraft standout during low light conditions. It is easy to use. You simply connect it to the balancing plug of your Lightning Power lithium polymer battery. Some types of battery balancing plugs have 2mm pin spacing. If this is the case, use the supplied adapter.

High quality Skid Nuts by Lightning Power designed to fit .50 - .90 size helicopters using standard skids such as Trex 600, Trex 700, Raptor .50, Raptor .90 and etc. This is one complete set.