These MAH Carbon main blades for the Piccolo CP/Pro are expertly molded and balanced. They are semi-symetrical and have a beautiful finish. They will give more lift and are more efficient than symetrical blades. Perfect choice for scale and general flying.

Same design and shape as the stock blades which ship with the Hornet II but these blades made by MAH from top quality Carbon Fiber. The blades are of the none tapered cord type and are specifically designed for 3D and aerobatic type flying.

The 393's are a great choice for 600 or 500 sized helicopters with a 3mm flybar. They are similar to the 3105's, however much more stable in fast forward flight.

These responsive paddles are perfect for your 450 sized helicopter. High speed and stable performance, plus they come with flybar weights so you can tune your setup to your liking.

Finally, extreme 3D maneuvers with stability. KBDD paddles also provide rock solid performance for FAI or scale flying. The paddles for the 50 size helicopters can accept a 3mm flybar while the paddles for the 90 size helicopters can accept a 4mm flybar. The paddles weigh approximately 15g and are weight matched to within .05g. The front flybar hole is threaded and will be the one most preferred. The rear hole should be used at your own risk as our pilots flew the most aggressive 3D maneuvers using the front hole. The rear hole can easily be threaded with the flybar taking care to remove the cuttings as you go.

Plastic paddles are inexpensive and yet produce great cyclic output making them ideal for normal or 3D flight. Best of all plastic rotor paddles are inexpensive so replacing them is not such a “budget breaker”. Plastic paddles also thread directly onto the flybar making them much safer. Available in black (.60 size ) or yellow (.30 size ). Yellow paddles make a unique yellow inner disk.

KBDD paddles are very light with a lot of surface area offering a great paddle for very fast 3D flight. Even faster than high end CF paddles as these paddles were made with thoughtful design both in shape and weight. They also have two flybar mount holes the forward hole increases stablility especially in Fast Forward Flight where the heli will have the tendancy to pitch up.

KBDD paddles are very light with a lot of surface area offering a great paddle for very fast 3D flight. Even faster than high end CF paddles as these paddles were made with thoughtful design both in shape and weight. They also have two flybar mount holes the forward hole increases stablility especially in Fast Forward Flight where the heli will have the tendancy to pitch up.

Beautiful white finish and smooth cutting edge provide the ultimate in cyclic response and stability .Featuring a beautiful carbon fiber smooth white finish these paddles look as good as they fly. Suitable for any helicopter with a 4mm flybar. Made by KSJ for any .60 - .90 size Nitro or Electric Helicopter. The paddles are held in place using the provided set screws.

The CF Blades are much stiffer than the plastic blades and will greatly reduce the conning effect which makes the Helicopter pitch up during forward flight. The blades are pre balanced and will allow for better flight control. Mounting washers included.

These are a direct bolt on for the Hornet CP. They are a cord taper design and have superior rigidity over all other blades. They will give much better cyclic response and they will make your Hornet track very well. The quality you expect from MAH.

These beautiful Thunder Tiger paddles are made of high quality composite and lock in place using the supplied set screws. The paddles are a direct replacement on the Raptor but can also be made to fit most other .60+ size Nitro Helicopters. Install on a 4mm thick flybar.

These CF blades are designed for the Collective Pitch Hornet. The blades are strong and precision crafted.

Designed and Flown by Mulit-Time World Champion Curtis Youngblood. These paddles provide aggressive response but still fly very stable in fast forward flight. Note: Make sure to set cyclics at maximum throws and the highest flybar ratio for best performance. Also paddles fly best at a higher RPM.

Similar in design to the Stubz paddles. However, these are longer and give your helicopter much more aggressive flight characteristics making them perfect for the 3D pilot. These weigh about 12 grams each and measure 105mm long. Designed and Flown by Mulit-Time World Champion Curtis Youngblood.

The perfect addition to your 50 sized helicopter. These paddles offer aggressive control while still maintaining smooth flight characteristics for those 3d pilots looking to get the max control out of their helicopters. In combination with the Radix blades you've got a winning setup for both the world champ and club aces alike.

Finally, extreme 3D maneuvers with stability. KBDD paddles also provide rock solid performance for FAI or scale flying. The paddles for the 50 size helicopters can accept a 3mm flybar while the paddles for the 90 size helicopters can accept a 4mm flybar. The paddles weigh approximately 15g and are weight matched to within .05g. The front flybar hole is threaded and will be the one most preferred. The rear hole should be used at your own risk as our pilots flew the most aggressive 3D maneuvers using the front hole. The rear hole can easily be threaded with the flybar taking care to remove the cuttings as you go.

Finally, extreme 3D maneuvers with stability. KBDD paddles also provide rock solid performance for FAI or scale flying. The paddles for the 50 size helicopters can accept a 3mm flybar while the paddles for the 90 size helicopters can accept a 4mm flybar. The paddles weigh approximately 15g and are weight matched to within .05g. The front flybar hole is threaded and will be the one most preferred. The rear hole should be used at your own risk as our pilots flew the most aggressive 3D maneuvers using the front hole. The rear hole can easily be threaded with the flybar taking care to remove the cuttings as you go.