This is a nice all aluminum Trex swashplate which is a direct manufacture replacement and will convert your Trex setup onto a CCPM direct servo link system. It will allow for a more precise cyclic control and will not break or fall apart as such is the problem with the stock plastic swashplate. All balls are a perfect fit and the lower plate includes the anti rotation pin. In this version with Anti Rotation Pin closest to the one arms !!!
select checkbox below:
T-Rex 450X All Aluminum CCPM Swashplate (Blue) 28.99 T-Rex 450X All Aluminum CCPM Swashplate (Grey) 36.99
- Kit Includes: Everything which shown in picture - Install in minutes and it is a direct replacement - Super CNC part which is recommended by the manufacture - Available in multiple colors
Metal Flybar Control Set (Blue)
Available in multiple colors
Are you looking to stiffen up your main flybar assembly even further ? The precision flybar control set come as a complete kit and rock over precision bearings for the least amount of bind and super smooth control. The silver rods / assembly are super light and very strong and the complete kit is a direct replacement.
select checkbox below:
Metal Flybar Control Set (Blue) 19.99 Metal Flybar Control Set (Purple) 20.99 Metal Flybar Control Set (Grey) 20.99
- Kit Includes: Everything which shows in picture - Install in minutes and it is a direct replacement - Super CNC part which is recommended by the manufacture - Available in multiple colors
TRex 90 Degrease Precision Swashplate
Use on V2 / Standard and HDE Kits
This top quality swashplate features a central bearing which allows only minimum free play of the whole cyclic system. Total up Weight is only 10g. This swashplate is the ticket for the ultimate stability in both hover and forward flying as well as 3D maneuverability. Specifically designed for the HDE and standard / V2 T-Rex 450X and XL.
35.00
PART#MT7420-90
- Tested for the ultimate stable performance - machined to perfection - Super smooth ball ends and Super smooth delrin center ball
Bell Crank and Tail Pitch Slider Combo Standard
Very High Quality Precision Part
The combo of Tail Pitch Lever and Tail Pitch Slider SE will provide much improvement with tail control. Includes a superior ball linkage system ( instead of pin system) the combo will reduce most the slop in the tail while providing best accuracy and control. Additional mounting holes give users option to change pivot point for the bell crank for greater flexibility in setup. Designed very light in weight and strong. With double precision bearings built in the unit it gives best precision tail controls and smoothness. Moreover the Tail Pitch Lever uses Delrin Insert and a CNC Metal Ball to achieve the best performance as well as durability. It is designed to improve tail controls performance on ALIGN T-REX helicopters.
select checkbox below:
Bell Crank and Tail Pitch Slider Combo Standard 44.99 Bell Crank and Tail Pitch Slider Combo XL 14.99 Bell Crank standalone with bearing only 24.99
- 100% Precision CNC machined Aluminum and Delrin - Pre-assembly 2 of 2x5x2.5mm precision miniature bearings. - Using Delrin Insert for light weight and longer lasting - Special reduced OD Steel Washer to prevent friction to outer ring of bearing - Light weight designs strong and stylish - Use a servo link and pin for light weight and to achieve tight control
Tail Pitch Slider - T-REX 450X
Very High Quality Precision Part
The Tail Pitch Slider (TPS) is designed very light in weight solid and strong. With dual bearing built in the unit gives the best precision tail controls and smoothness you can get up to 20 000RPM. The Tail Pitch Slider unit including High Strength Plastic TPS Horn is 100% made from CNC machines for maximum accuracy and consistent tail pitch controls. The TPS Horn design has been redesigned to maximize precision tail controls reducing stress and binding on stock design. The Metal Pin is also used on this TPS for secure and compatible with stock plastic bell crank. It is designed to improve tail controls performance on T-REX 450X helicopters.
34.99
PART#MH-TX4193
- 100% Precision CNC machined Aluminum and Delrin - Pre-assembly 2 of 4x8x3mm precision bearings - New designed and improved CNC High Strength Plastic TPS Horn for maximum performance and accuracy - Using Metal Pin for secure and tight controls during operation - Light weight designs strong and stylish - This Part is compatible with all the stock plastic parts
HeliHobby.com is your source for Remote Control RC Helicopters, products, modifications and more. Full Range of Nitro, Electric and Micro Helis in stock