Tail blade grips only, rear half of heli not included
Weighted tail blade grips are proven effective and functional on full sized helicopters and RC helicopters.
The G-Force weighted CNC tail blade grips are a bolt-on upgrade with performance that you can feel.
The weights are used to reduce the momentum of the blades that have a tendency to center themselves. These natural forces put extra load on the tail servo and reduces its response.
The G-Force tail blade grips incorporate weighted flanges closest to the center near the hub and linkage point for best performance. The flange is also pre-tapped so you can add more weight if necessary to fine tune your setup.
The 450 version (Part #GFT6010) will fit both T-Rex 450 V1 and V2.
A V2 hub is required.
Ultimate Power Pack for the 450 Class
Run a 6s Lipo on your 450!
The benefit of increasing the voltage in your setup is no secret. This power package allows you to run a 6 cell lipo on your Trex 450 or other 450 class helicopter. A 6 cell lipo is much more efficient, increasing power and decreasing heat. We packaged this with quality components including the Castle Creations 50AMP LITE ESC w/Data Logging to power your motor using the built in switching BEC to run your electronics. The Lightning Power 6s 1300mah battery included in this package was specifically designed to fit a 450 class helicopter such as the Trex 450. This setup is extremely powerful but the benefits achieved by a cooler running setup yields interest from every kind of R/C heli pilot.
This package has been updated to use the new Castle Creations Phoenix ICE Lite ESC. The Phoenix ICE has built in data logging and a switching BEC which is more than adequate to power full digital servos/gyro on your 450 class heli.
This discount package comes with the following products: - CSEM6000 Lite 50A / 25V
- LP-B1133 Lightning Power 1300mAh 25C 6S1P 22.2V Li-Po 3G
- HK-2221-1630 Scorpion HK-2221-1630 V2 HK-2221-1630
- CASTLE-PHX-LINK USB Computer Programming Kit for Phoenix Controllers
- LP-C1015 Lightning Power T Style Male and Female connectors
Align 400 size Heli Main Blade Holder/New ( AGNH1001 / HS1181 )
Hold main rotor blades in place
Two tone blue and back Main Blade Holder for 400 size helicopters such as the Trex, X-400, Zoom Shogun, Park-Mite from JR and others. Safe guards main rotor blades while carrying the Heli around.
- For Trex 450 V2 with 4mm feathering shaft
- Damper rubber x 2(Φ4xΦ6.5x4mm)
- Washer x 2(Φ5.5xΦ8x0.4mm)
450 Landing Skid Set White
- USE for T-REX 450 SE/V2/PRO
Includes:
- Landing skid x 2
- Skid pipe x 2(Φ5.5x180mm)
- Skid pipe end cap x 4
- M2 Set screw x 4(M2x2mm)
- Hex head wrench x 1(0.9mm)
- Socket button head self tapping screw x 4(T2x10mm)
T-Rex Hardware Bag
Four sets per pack
Hardware Bag with shake proof nuts and hex screws.
A beautifully finished woven boom and attached as a direct replacement to the stock softer aluminum boom.
The boom is very stiff and attractive.
Stiffer boom assist in the total rigidity of tail setup as well as tail control. Perfect fit and will produce the most stable center of gravity setup on the Trex 450X/XL.
Carbon works very well with the belt as it a smooth / bind free surface.
- Direct replacement / installation to Heli
Hardware Bag XL / SE (HZ027 / AGNH1150)
Hardware Bag
Lightning Power 325mm GF High-Performance Blades
325mm Glass Fiber Blades designed by Lightning Power with the goal of making a low cost 3D ready blade available. Made of High-Grade materials using a proven design these blades make a great choice over the wooden blades.
Lightning Power 325mm GF High Performance Blades - Bundle and Save
PART# LP-M0112
325mm Glass Fiber Blades designed by Lightning Power with the goal of making a low cost 3D ready blade available. Made of High-Grade materials using a proven design these blades make a great choice over the wooden blades.
T-Rex 325mm PRO Rotor Blade Black ( AGNH325WB / HS1158-00 )
Inexpensive and rigid T-Rex 325mm PRO Rotor Blade available in Black with white decal or in white with red decal.
